# GE-RCV1: Richmond remote to operate the garage and gate motors

> Wire a 1-channel GE-RCV1 receiver to a Steel-line SD1200 garage motor, so the Richmond gate remotes open the garage too. Includes the receiver's real wiring, which its manual doesn't show.

Guide · Published 2026-10-11 · Updated 2026-10-11  
Web page: https://blog.jacq.cc/guides/ge-rcv1-garage-gate-remote/  
Discuss on Hacker News: https://news.ycombinator.com/item?id=50049234

Our gate remotes have spare buttons. A small 433 MHz receiver at the garage motor turns one of them into a garage opener, so there's just one remote on the key ring instead of two.

[Image: A drawing of the GE-RCV1: a glossy black box labelled GE-RCV1 and AC-DC-12V-24V, with a white LEARN button and a glowing red LED, its antenna catching radio waves from a gate remote, red, black and yellow wires curling out of the bottom, and a garage door rolling up behind it]

*The GE-RCV1, drawn from mine. Photos of the real one, outside and in, are in [step 3](#step-3-know-the-receivers-wires).*

:::note[Status, October 2026]
Working - a spare button on our gate remotes opens and closes the garage. Still to come - Home Assistant control, with an ESP32-C6 on Zigbee ([the plan](#next-home-assistant-control)). This guide gets updated when that's built.
:::

## What you need

| Part | Notes |
| --- | --- |
| GE-RCV1 receiver, 1-channel (label `GE-RCV1 AC-DC-12V-24V`, code SC2504004) | 433.92 MHz. Sold as an add-on receiver for Richmond gate kits |
| A gate remote with a spare button | Mine came with a Richmond GTR156 sliding gate |
| A garage motor with a push-button input | A Steel-line SD1200 here. Most openers have one - it's where a wired wall button goes |
| Multimeter, small flat screwdriver, a short insulated wire | |
| Optional: a 12 V DC supply | To bench-test the receiver before it goes near the motor |

About 45 minutes, including the bench test.

[Image: A grey Richmond GTR156 sliding gate motor at ground level beside the gate, the toothed rack along the gate's bottom rail, and the weatherproof power point it plugs into]

*Our gate's motor, a Richmond GTR156. Its remotes are the ones this guide reuses.*

## How it works

A garage motor's push-button input is a pair of terminals. Shorting them for under a second does the same as pressing a wall button - open, stop, close, stop, in turn. The receiver has a relay that closes for a moment when it hears a paired remote button. Put that relay across the push-button terminals, and the remote button becomes a wall button.

## Step 1: Test the motor's push-button input

The SD1200's terminal block reads `Receiver | Receiver | com | +24VDC` (installation manual, page 7).

1. Clear the door's path, it will move.
2. Touch an insulated wire across the two `Receiver` terminals for under a second, then take it away.
3. The door starts. Each short moves it to the next step - open, stop, close, stop.

On my SD1200 this actually worked first time.

:::caution[The terminal tabs are fragile]
I pushed a wire in too hard and the `com` tab came off the board. It took a few minutes to seat it back, and it works again. Push wires in firmly enough to make contact, but don't force the tabs. A wire can feel tight and still not touch the contact, so check each one with the multimeter.
:::

## Step 2: Find the common side of the input

The receiver's output isn't a floating contact (step 3 shows why) - one side of it is the receiver's own power wire. So in step 4 one `Receiver` terminal gets joined to `com`. That's only safe if the motor already joins them inside.

1. Switch the motor off at the wall.
2. Multimeter on continuity. Test `com` against each `Receiver` terminal. One should beep (close to 0 Ω), and that's the common side. Mark it.
3. Switch the motor on. DC volts between `com` and `+24VDC` should read about 24 V. That's the receiver's power.

If neither `Receiver` terminal beeps to `com`, don't use the wiring in step 4. Make the receiver's output a dry contact first ([below](#want-a-dry-contact)).

## Step 3: Know the receiver's wires

The closest manual is for Richmond's GTR197, the 4-channel version. That one has a 2-core power cable and a 5-core output cable. The 1-channel unit has 3 wires (red, black, yellow) plus the antenna, so the manual's wire colours don't apply. I opened it to see where they go.

[Image: The GE-RCV1 1-channel receiver, closed: LEARN button, LED, three wires and the antenna]

[Image: The board: one relay (K1, right), empty spots for K2 to K4, and the J3 connector on the left]

Inside there's one relay, K1 (a Y14H-1C-5DS). The spots for K2 to K4 are empty. The wires plug into connector J3, printed `AC, AC, CH1, COM, CH2, CH3, CH4`:

| J3 pin | Wire |
| --- | --- |
| `AC` (1) | black, plus a short black jumper to `CH1` |
| `AC` (2) | red |
| `CH1` | the other end of that jumper (inside the case only) |
| `COM` | yellow |
| `CH2` to `CH4` | nothing |

[Image: J3 close-up: the black jumper loops from AC to CH1, yellow sits on COM]

What that means:

- Power goes in on red and black. Both `AC` pins feed a bridge rectifier (the B6S next to J3), so 12 to 24 V, AC or DC, either way round, works.
- The output is the relay switching `COM` to `CH1`, and the jumper ties `CH1` to `AC` (1), the black wire. So the output is yellow to black - open at rest, shorted while a paired button is pressed.
- Polarity matters for the output. Black is both a power wire and one side of the output, so black must go to the motor's common side.

## Step 4: Wire it to the motor

Motor off at the wall first.

| GE-RCV1 wire | SD1200 terminal |
| --- | --- |
| red | `+24VDC` |
| black | `com`, and also the `Receiver` terminal that beeped to `com` in step 2 |
| yellow | the other `Receiver` terminal |

When the relay closes, yellow joins black, which shorts the two `Receiver` terminals - the same as the wire in step 1. Mine is wired exactly like this, and it works.

[Image: Looking up at the Steel-line SD1200 on the garage ceiling, with the black GE-RCV1 box mounted on top of the motor and its wires running to the motor's terminals]

*Mine, wired and working - the GE-RCV1 (the black box on top) on the Steel-line SD1200.*

## Step 5: Pair the spare remote button

These are the GTR197 manual's steps (page 2). Pairing the 1-channel unit worked for me.

1. Press "LEARN" on the receiver once. The LED stays on.
2. Press the spare remote button twice. The LED flashes 2 or 3 times, then goes off - paired.
3. Press the button again. The garage door starts.

## Optional: bench-test it first

Power the receiver from a 12 V DC supply on the bench (red and black, either way round) and pair the remote as in step 5. Put the multimeter on continuity between yellow and black, and it beeps briefly on each press. That way nothing can surprise you at the motor.

## Want a dry contact?

Take the short jumper between `AC` (1) and `CH1` out of J3, and bring `CH1` out as a fourth wire. Yellow to that new wire is then an isolated contact, and it can go across any push-button input, whichever way round.

## Next: Home Assistant control

Not built yet. The push-button input happily takes a second trigger in parallel with the receiver. The parts are here already - a Seeed XIAO ESP32-C6 and a 3 V relay module (Songle SRD-03VDC-SL-C) for each motor. The C6 has a Zigbee radio, so it joins Home Assistant over Zigbee, like the door's contact sensor already does.

[Image: A Seeed XIAO ESP32-C6 in its plastic tub, and a 1-channel relay module with a blue Songle relay and screw terminals]

*The parts for the next step - the XIAO ESP32-C6 (still in its tub) and the 3 V relay module.*

- A button in Home Assistant pulses the relay for about half a second.
- The relay must stay off while the ESP boots, so a reboot or power cut never moves the door - a pin with no boot role (D0 to D3 on the XIAO), and firmware that starts with the relay off.
- Door state comes from a Zigbee contact sensor, not the relay. One input does open, stop and close in turn, so the relay alone can't know where the door is.
- Power from the motor, with a 24 V to 5 V buck converter on the SD1200's `+24VDC` and `com`.
- The gate's controller (Richmond GTR156) has a 15 V accessory output and two inputs - open/stop/close, or open only, which can never close the gate on someone. Its manual says changes inside the controller are for a licensed electrician.

[Image: The yellow label on top of the gate motor: Richmond Wheel & Castor Co, Rolling Solutions, model GTR156, automated gate opener, 230 to 240 V AC 50 Hz, IP54]

*The label on top of our gate motor - model GTR156.*

That gets its own guide once it's built.

## Manuals

- [Steel-line SD1200 installation manual](https://www.steel-lineautomation.com.au/uploads/7/2/0/3/7203835/installation_manual_sd1200-v1__0719_.pdf) (PDF)
- [Richmond GTR197 external receiver manual](https://www.richmondau.com/wp-content/uploads/2021/12/GTR197_external_receiver_v8.25o.pdf) (PDF): the 4-channel receiver; its pairing steps work for the GE-RCV1
- [Richmond GTR156 gate motor manual](https://www.richmondau.com/wp-content/uploads/2019/04/GTR156-instruction-manual.pdf) (PDF)

## Change history

- 2026-10-11: First published.

Licence: CC BY 4.0 (https://creativecommons.org/licenses/by/4.0/). Credit "HomeLab Series (blog.jacq.cc)" with a link to https://blog.jacq.cc/guides/ge-rcv1-garage-gate-remote/. Code downloads: MIT. Details: https://blog.jacq.cc/licence/
